In New York City, emergency power is a code requirement tied to your building's size, occupancy and life-safety systems, not an optional upgrade. Chapter 27 of the NYC Building Code (BC 2702) decides which buildings need emergency power, which need standby power and which need both. Fire Code Section 604 then sets how you test the system for as long as the building stands. Getting the classification right at the start decides the generator or battery size, the room it sits in, the permits you file and the inspections you pass. Because that work crosses electrical, mechanical, plumbing and fire protection design, it is best planned by one engineering team that knows how the NYC Department of Buildings (DOB) and the Fire Department (FDNY) review it.
TL;DR
- NYC code separates emergency power (life-safety loads, restored within 10 seconds) from legally required standby power (selected loads, within 60 seconds) and optional standby power (owner-chosen loads).
- BC 2702.2 lists the buildings and systems that need each type. High-rises, assembly spaces, covered malls, underground buildings and many elevators and fire pumps are covered.
- Fuel-based systems generally need at least six hours of on-site fuel at full demand, and required stationary generators must be UL 2200 listed and sit in a dedicated two-hour rated room.
- Battery energy storage and UPS systems follow new rules: ESS rules effective October 26, 2025, and DOB Buildings Bulletin 2026-013 issued September 3, 2026.
- Once installed, the system must be tested under load on an approved schedule, with written records.
Table of Contents
- Emergency, legally required standby and optional standby: the three categories
- Which NYC buildings need emergency or standby power
- Power source, fuel, room and transfer requirements
- Battery storage and UPS: the newest rules
- Existing buildings: adding or replacing emergency power
- Testing, records and inspection
- A practical sequence for an emergency power project
- How we handle emergency power work
- Work with the team that designs it
- Our perspective on emergency power in NYC
- FAQ
Emergency, legally required standby and optional standby: the three categories
NYC code uses three terms that owners often treat as one. They are not interchangeable, and the category sets nearly every design decision that follows.
| Category | What it serves | Restoration time | Separation from normal power |
|---|---|---|---|
| Emergency | Life-safety loads: egress lighting, exit signs, fire alarm, voice/alarm communications, fire pumps, life-support equipment, certain elevator components | Within 10 seconds | Completely separate: own conduit runs, panels, transfer switches and dedicated rooms |
| Legally required standby | Selected loads in certain facilities that help occupants evacuate and help firefighters operate: smoke control, stair pressurization, required elevators | Within 60 seconds | Required by code, but need not be fully separate |
| Optional standby | Loads the owner chooses, such as a tenant computer room | Manual or automatic | May share components with normal power |
The NYC DOB's emergency backup power project page is where most filers start, but the practical point is simple: the 10-second and 60-second figures mirror the National Electrical Code split between Article 700 (emergency) and Article 701 (legally required standby). A generator that can pick up a load in 40 seconds is perfectly acceptable for a smoke-control fan and unacceptable for egress lighting. That is why the load list is drawn up before equipment is chosen.
Which NYC buildings need emergency or standby power
BC 2702.2 is the controlling list. In summary, emergency power is required for systems such as:
- Voice/alarm communications in Group A assembly occupancies and malls
- Exit signs and egress illumination
- High-rise and underground buildings
- Doors in Group I-3 (correctional) occupancies
- Certain hazardous-material occupancies and semiconductor fabrication facilities
Standby power is required for systems such as smoke control, accessible means of egress elevators, horizontal sliding doors, membrane-structure auxiliary inflation, airport traffic control towers and elevators in specified buildings.
Section BC 2702.2.20 catches many mid-size buildings that owners assume are exempt. It requires both emergency and standby power in:
- Group B (business) and Group E (educational) buildings whose occupied floors are less than 75 feet above the lowest level of fire department vehicle access and that have more than 15,000 square feet per floor or more than 100,000 square feet in total
- All Group R-1 occupancies, which means hotels and similar transient lodging
In those buildings, the emergency loads include exit signs, egress lighting, elevator car lighting, voice/alarm communications (including in-building auxiliary radio communication systems), automatic fire detection, fire alarm and electrically powered fire pumps. The standby loads include smoke venting and control ventilation, stair pressurization, at least three elevators operating at one time and fire command center power and lighting.
Elevators
Elevators are the most frequent source of confusion. DOB Buildings Bulletin 2017-008 lists the categories that need standby power: high-rise elevators under BC 403.4.7.2, Group R-2 high-rise elevators in buildings over 125 feet under BC 403.4.7.3, underground building elevators under BC 405.8, certain Group B, E and R-1 elevators under BC 2702.2.20 and accessible means of egress elevators under BC 1007.4. BC 3003.1 then governs how that standby power is used during emergency operation, such as firefighter recall.

Optional standby generators carry obligations too
A building owner who installs a generator purely for a tenant's server room has not escaped the code. BC 2702.4, clarified in Buildings Bulletin 2015-002 (March 6, 2015), requires an optional standby system to also back up emergency lighting, fire alarm systems and qualifying elevators, unless a working emergency or legally required standby system already supplies those loads. For Group R-2 buildings over 125 feet, or any building with occupied floors more than 75 feet above fire department vehicle access, that means at least one elevator serving all floors (or one per bank). These systems must comply with UL 2200 and NFPA 110 and get special inspection under BC 1704.31.

For a property manager, the lesson is to settle the tenant request and the code obligation in the same design, not as two projects.
Power source, fuel, room and transfer requirements
BC 2702.1 requires installation in accordance with the NYC Electrical Code, NFPA 110 (engine-driven generator systems) and NFPA 111 (stored electrical energy systems). The recurring requirements are these:
- Capacity. Under BC 2702.1.3, the system must supply all equipment required to run at the same time. Undersized generators are a common failure at final inspection, usually because a load was added after the design.
- Fuel. Under BC 2702.1.1, fuel-based systems generally need an on-premises supply for at least six hours of full-demand operation. Natural gas from the public street main is permitted as the sole fuel for emergency systems in Group R-2 occupancies, for emergency systems permitted by Appendix G and for standby systems. It requires an outside gas cut-off valve, separate from other gas services, under Fuel Gas Code Appendix E, Section E.6.
- Listing and room. Required stationary generators must be UL 2200 listed, kept out of the main electrical service equipment room and installed in a dedicated room with at least two-hour fire separation.
- Fire pumps. BC 2702.1.4 requires Electrical Code-compliant overcurrent protection and feeder conductors for electric fire pumps on emergency power, with the automatic transfer switch in the fire-pump room as an integral part of the controller. NEC Article 695 adds supervision against inadvertent disconnection and sizing rules for the overcurrent device.
- Temporary generator connections. Where an emergency system relies on a single alternate source, NEC 700.3(F) from the 2020 edition calls for a permanent switching means to connect a portable or temporary source. That inlet needs transfer within 10 seconds, phase rotation and bonding markings, interlocking so the sources cannot be tied together and annunciation. Connecting the temporary source must not require modifying the permanent wiring.
- Load priority. When capacity is limited, load shedding under NEC 700.4(C) keeps emergency loads first, then legally required standby, then optional standby.
This is where fuel logistics also matter after design. For a data-center style continuity plan, fuel planning and emergency resupply is covered in a dedicated 2026 checklist.
Battery storage and UPS: the newest rules
Two recent changes affect any owner considering batteries in place of, or alongside, a generator.
Energy storage systems (ESS)
Effective October 26, 2025, the DOB added 1 RCNY 101-19 and 1 RCNY 3616-07, which adopt a modified NFPA 855. For indoor ESS above the capacity thresholds, the rules call for:
- UL 9540 listing
- UL 9540A large-scale fire testing, unless NFPA 855 exempts the technology
- An FDNY Certificate of Approval
- Siting separation distances, fire detection and suppression
- An emergency response plan prepared before commissioning
The lithium-ion threshold is 1 kWh, lowered at FDNY's request. Vented lead-acid and nickel-cadmium batteries in standby and emergency applications are excluded from large-scale testing. Outdoor ESS must comply with FDNY rules, and all ESS in one- and two-family dwellings is covered.
UPS as an emergency source
Buildings Bulletin 2026-013 (September 3, 2026) explains how the 2025 NYC Electrical Code, Section 700.12(E), treats a UPS. A UPS is now allowed as an emergency power source without the special permission the 2011 Electrical Code required, but with limits:
- If a stationary generator is installed under the 2022 Building Code, a UPS may not supply loads that require emergency power.
- Without a generator, a UPS may supply the fire alarm system and in-building auxiliary radio communication system if it uses lead-acid batteries, complies with NFPA 111-2013 and NFPA 72 Appendix Q, and uses UL 1989 or UL 1973 batteries in a UL 1481 or UL 864 listed system.
- It must be sized for at least six hours of full fire alarm and radio communication load, be dedicated and placarded, and have aggregate capacity no greater than 70 kWh.
- The UPS room must be two-hour fire-rated with smoke detection, ventilation of at least 1 cfm per square foot (not required on emergency power for sealed VRLA batteries) and fire suppression.
- Installation needs an electrical permit from a NYC-licensed electrical contractor and a final electrical inspection.
A UPS can look like the cheap shortcut for a small building. The bulletin shows it is a narrow path with its own room, listing and permit demands, so the choice belongs in early design.
Existing buildings: adding or replacing emergency power
Most NYC work is in existing buildings. The DOB states that work to install or modify emergency backup power must comply with the Zoning Resolution, the Building, Fuel Gas and Mechanical Codes, the Electrical Code, the Fire Code and the Energy Conservation Code. Under Administrative Code 28-101.4.3, alterations and repairs conform to new-installation requirements without necessarily forcing the whole existing installation to comply, but they cannot make it unsafe, hazardous or overloaded.
In practice, one generator replacement touches several trades:
- Electrical: feeders, transfer switches, panels and the separation of emergency circuits.
- Mechanical: combustion air, exhaust, ventilation and fuel storage.
- Plumbing and gas: gas piping and the outside cut-off valve for natural gas units.
- Fire protection: suppression and detection in the generator or battery room, plus fire pump connections.
New fire pumps in existing buildings must also be connected to an emergency power system, so a pump upgrade can trigger a power upgrade.
Testing, records and inspection
Fire Code Section 604 puts ongoing duties on the owner. Emergency power systems and their components must be periodically inspected and tested under load under NFPA 110 (as modified by Fire Code Appendix B) and NFPA 111. The rules include:
- A schedule. An approved schedule is set when the installation is completed and approved (604.3.1).
- Records. Written service records note the date, technician name, conditions found and corrective actions (604.3.2).
- Supervision. Testing is supervised by a DOB-licensed electrician, stationary engineer, certificate of fitness holder or registered design professional (604.5).
Before that, the installation itself is inspected. BC 2702.1.5 requires special inspection under Section 1705. The DOB may also inspect plumbing and gas work, fuel oil storage, final electrical and final construction sign-off, with the inspector checking that field conditions match approved documents and that equipment is connected as shown on the electrical diagram, including the main service panel connection.
Owners who want the test schedule to hold up should keep the approved design documents with the building records, so the person supervising each test works from the same load list the DOB approved.
A practical sequence for an emergency power project
- Classify the building. Confirm occupancy group, height above fire department vehicle access and floor area against BC 2702.2. Identify every elevator and fire pump.
- Build the load list. Sort loads into emergency, legally required standby and optional standby, and add tenant requests so the BC 2702.4 obligations are captured.
- Choose the source. Generator, natural gas, battery ESS or a limited UPS. Check fuel duration, listings and room requirements for each.
- Design the room and the paths. Two-hour separation, dedicated emergency conduit and panels, transfer switch location, ventilation and suppression.
- File and permit. Prepare the DOB filings and FDNY submissions, including the Certificate of Approval for ESS.
- Inspect and commission. Special inspections, final electrical and construction sign-off.
- Set the test schedule. Record the Fire Code 604 schedule and who supervises it.
Steps 2 and 4 are where projects slip. A load added after approval can force a larger generator, a new room layout and a re-filing.
How we handle emergency power work
Emergency power does not fit inside one trade. The generator room is a mechanical and electrical problem, the gas line is plumbing, the suppression is fire protection and the approval path runs through the DOB and FDNY. Bazini Engineering keeps mechanical, electrical, plumbing and fire protection design in-house, which lets one team coordinate the load list, the room, the permit drawings and the agency filings. Our NYC permit filing service covers the DOB side, and owners who are deciding whether to replace aging plant can start with building evaluations and capital planning. If a fire pump is part of the project, our fire suppression engineering page explains that scope.
Work with the team that designs it
If you are planning a new generator, a battery system, a fire pump upgrade or a review of whether your building meets BC 2702, Bazini Engineering, P.C. can take the project from evaluation through design and filing. We have served New York City, Long Island and Westchester since 2010, with direct access to senior engineers rather than account managers. See the full range on our services page.

Bring your occupancy group, building height and the systems you need to keep running, and we will start from the BC 2702 classification.
Our perspective on emergency power in NYC
Most emergency power problems we see in the planning stage come from treating the generator as the project. The generator is the easy part. The hard part is deciding which loads belong in which category, because that decision sets the room, the separation, the fuel, the transfer equipment and the filings.
Our view is that this work should be designed as one coordinated MEP/FP package. When the electrical, mechanical, plumbing and fire protection engineers sit in the same firm, the gas valve location, the room ventilation, the suppression and the transfer switch are settled together instead of being passed between consultants. That is how we aim to keep a project moving through DOB and FDNY review.
For owners weighing batteries, the 2025 ESS rules and the 2026 UPS bulletin make early design more important, not less. Settle the technology against the code before you commit to equipment.
Joseph
FAQ
What is the difference between emergency power and standby power in NYC?
Emergency power serves life-safety loads such as egress lighting, fire alarms and fire pumps, and must be restored within 10 seconds on completely separate wiring. Legally required standby power serves selected loads such as smoke control and required elevators, within 60 seconds. Optional standby serves loads the owner chooses, though BC 2702.4 can still require it to back up life-safety loads.
Does my building need a generator?
It depends on occupancy, height and floor area. High-rises, underground buildings, assembly spaces, covered malls and all Group R-1 occupancies are covered by BC 2702.2. Certain Group B and E buildings are covered above 15,000 square feet per floor or 100,000 square feet total. An engineer can check your building against the list.
How long must fuel last?
Fuel-based systems generally need at least six hours of on-premises fuel at full demand under BC 2702.1.1. Natural gas from the street main is permitted as the sole fuel for standby systems and for emergency systems serving Group R-2 occupancies, with a separate outside gas cut-off valve.
Can batteries or a UPS replace a generator?
Battery ESS above the thresholds must meet the October 26, 2025 rules, including UL 9540 listing and an FDNY Certificate of Approval. A UPS can supply the fire alarm and in-building radio communication system only when no stationary generator is installed under the 2022 Building Code, and within the limits in Buildings Bulletin 2026-013.
How often must the system be tested?
Fire Code 604 requires periodic testing under load on a schedule approved when the installation is completed, with written records. The testing must be supervised by a DOB-licensed electrician, stationary engineer, certificate of fitness holder or registered design professional.
