In New York City, a duct smoke detector is required when the building code or the Mechanical Code says an air-handling system must shut down or close dampers on smoke. The usual triggers are return-air systems over 2,000 cfm, supply-air systems over 2,000 cfm, high-rise buildings and underground buildings with smoke control. Under the 2022 codes, the detector must report as an alarm signal at the fire alarm control panel. It is an HVAC control device and never a substitute for room smoke detection. Getting the type, location, wiring and testing right is an engineering coordination job between mechanical and fire protection, and that coordination is where filings and inspections most often stall.
This guide is for building owners, property managers, HVAC and boiler installers, plumbers and registered architects who need the rules in plain terms. Where we cite a code section, check the edition that applies to your filing date.
TL;DR
- A duct smoke detector samples air inside an HVAC duct to shut fans and close dampers. It does not replace open-area smoke detectors, according to FDNY's Certificate of Fitness study material.
- The 2022 NYC Mechanical Code §606 calls for detectors in return-air and supply-air systems designed for more than 2,000 cfm, and §606.1 requires UL 268A listing.
- Under the 2022 Building Code, duct detectors report as an alarm signal at the fire alarm control panel. The 2014 option of a supervisory signal is gone.
- Placement depends on your filing date. DOB Bulletin 2014-004 governs projects filed before 12/31/14, and the 2022 codes govern newer work.
- Detectors connected to a fire alarm system need visual inspection and cleaning at least every six months and a smoke-entry and sensitivity test at least annually.
Table of Contents
- What a duct smoke detector does, and what it does not
- When NYC requires duct smoke detection
- Where the detector goes
- Connecting to the fire alarm and controlling HVAC
- Inspection, cleaning and testing
- What drives the cost
- Where projects go wrong
- Our perspective
- Getting your building reviewed
- FAQ
- Sources
What a duct smoke detector does, and what it does not
A duct smoke detector sits on or in an HVAC duct and samples the air moving through it. When it senses smoke, it signals the fire alarm system, which stops fans and closes smoke dampers so the air system does not carry smoke from the fire floor to the rest of the building.
The terminology matters in filings. NFPA draws the line this way: a smoke detector is a sensor connected to a building-wide fire alarm system, while a smoke alarm pairs a sensor with its own sounder for occupants. A duct detector is the first kind. Its job is to report and to control equipment, not to warn people in the room.
FDNY's study material for the S-78 and F-78 Certificates of Fitness says duct detectors sample HVAC air and help control air movement, and are not a substitute for open-area smoke detectors. It also says their locations must be identified and recorded. There is a physical reason for the limit. When ventilation is off, smoke may never enter the duct. When it is running, smoke can be diluted before it reaches the sensor. A duct detector therefore cannot stand in for detection in the occupied space.
The Building Code says the same thing in its own words. Section 907.3.1 requires duct detectors to be listed for duct conditions and connected to the fire alarm control unit when a fire alarm system is required. It adds that they cannot replace required open-area detection.

When NYC requires duct smoke detection
The requirement comes from more than one place, and the sections point to each other. Here are the ones that decide most projects.
Return-air and supply-air systems over 2,000 cfm
The 2022 NYC Mechanical Code §606.2.1 requires smoke detectors in return-air systems designed for more than 2,000 cfm. They go in the return duct or plenum, before filters and before the specified air connections. Section 606.2.4 covers supply-air systems with capacity greater than 2,000 cfm. There, listed detectors go downstream of the air filters and upstream of the branch connections.
Capacity is the design airflow of the system, so an air handler you size at 2,400 cfm is in scope even if it usually runs below that. This is a common point of confusion on retrofits, where an existing unit's nameplate and the as-built airflow do not match. Reconcile them before you decide the detector is not needed.
High-rise and underground buildings
Building Code §907.2.13.1.2 sends high-rise duct smoke detection to Mechanical Code §606, so the same airflow thresholds apply. For underground buildings with a compartment smoke-control system, §907.2.18.1 requires detectors in the main supply, main return and exhaust plenums of air-conditioning systems serving more than one story. It also requires them at each return-duct or plenum connection to a vertical riser serving two or more floors. The code gives Group R (residential) an exception for risers at or below 5,000 cfm that serve no more than 10 inlets.
Smoke dampers
Where a smoke damper is required, Mechanical Code §607.3.3.2 requires it to close when a listed duct smoke detector, installed under §606 and Building Code §907.3, is actuated. The detector or its sampling tubes must be within 5 feet of the damper, with no air outlets or inlets between the detector and the damper.
Two quick tests for scope
Ask these questions of every air-handling unit on the job:
- Does the unit move more than 2,000 cfm on the supply side, the return side or both?
- Does it serve more than one story, or a riser that does?
- Is a smoke damper or fan shutdown required in its path?
A yes to any of these puts the unit in the detection scope, and the design should say so on the drawings rather than leave it to the installer.
Where the detector goes
Placement is where installers and engineers most often disagree, because the answer depends on the code edition and the system type. There is no single distance from the air handler that applies to every case.
Position in the airstream. For return systems, the 2022 Mechanical Code puts the detector in the return duct or plenum before filters. For supply systems, it puts it after the filters and before the branches. This keeps filters from stripping smoke before it reaches the sensor on the return side and keeps the detector upstream of where air divides on the supply side.

Entire airflow. Section 606.3 requires the detector to monitor the entire airflow the system conveys. Where one unit has multiple return openings, a single detector in one branch may not meet that test.
Access. The same section requires access for inspection and maintenance. Duct detectors above hard ceilings, behind equipment or in shafts with no panel are a frequent failure at final inspection, and a recurring cost for the owner afterward. Show the access path on the drawings.
Five-foot rules. DOB Bulletin 2014-004 applies to projects filed before 12/31/14. It specifies a detector within 5 feet downstream of an electric duct reheat coil and before any supply-duct branch outlet. It also gives five-foot placements at particular smoke dampers. It does not state one distance from every air handler. If you are working on a building with an older filing history, confirm which rule your approved plans were filed under before you move or add a device.
Connecting to the fire alarm and controlling HVAC
A duct detector that is installed but not wired correctly does nothing. Three links must work together.
Fire alarm connection. Under Building Code §907.3.1, when a fire alarm system is required, the detector connects to the fire alarm control unit. Activation initiates a visible and audible alarm at a constantly attended location, subject to the code's exceptions.
HVAC response. Bulletin 2014-004 describes supply-fan shutdown and associated damper closure under its stated conditions for older filings. The design has to say which fans stop, which dampers close and what happens to return and exhaust fans. Those decisions belong to the mechanical engineer, while the fire alarm engineer shows the signal path.
Signal type. This is the biggest change from the older rules. The DOB's 2022 code update presentation explains that under the 2022 Building Code, duct detectors must report as an alarm signal at the fire alarm control panel, triggering an FDNY-approved central station response. The 2014 code allowed a supervisory signal. The same presentation notes that R-2 fire alarm requirements now mandate smoke detection in mechanical and electrical rooms regardless of square footage. For an owner, that means a duct detector in alarm can bring the fire department, so a dirty or poorly set detector costs more than it used to.
Listing. Mechanical Code §606.1 in the 2022 edition requires duct smoke detectors to comply with UL 268A, the product standard for smoke detectors for duct applications, as reported by Green Light Expediting. Check the cut sheet of any detector you buy against that listing before it arrives on site.
| Item | Before 12/31/14 filings | 2022 codes |
|---|---|---|
| Governing guidance | DOB Bulletin 2014-004 | 2022 Building Code §907, 2022 Mechanical Code §606 and §607 |
| Signal at the panel | Could be supervisory | Alarm signal, with FDNY-approved central station response |
| Airflow trigger | Per bulletin and code in force | Over 2,000 cfm for return and supply systems |
| Listing | Per the code in force | UL 268A required under MC §606.1 |
Inspection, cleaning and testing
FDNY's study material says air-duct detectors should be tested or inspected to verify that they sample the airstream. For smoke detectors connected to a defined fire alarm system, it calls for visual inspection and cleaning at least every six months and testing for smoke entry and sensitivity at least annually.
In practice, that means three things for the building owner:
- Put it on the calendar. The six-month cleaning and annual test should be scheduled items, not discovered at a violation.
- Keep the device list. The study material says detector locations must be identified and recorded. A current schedule of every duct detector, by unit and floor, saves hours at each test.
- Test with the fans running. A detector can be fine on the bench and still fail to sample the airstream. Since smoke may not enter a duct when ventilation is off, the test conditions matter.
For installers, the point to remember is that testing is more than pressing a button. Fan shutdown, damper closure and the panel signal should all be confirmed in one sequence, and each result recorded.
What drives the cost
Specific prices vary widely by building and by the vendor's scope, so a number copied from a generic price page is a poor budget basis for a New York job. What moves the total is consistent from job to job:
- Access. Lifts, ceiling work and shaft access add labor, and in occupied buildings add off-hours work.
- Duct size and condition. Larger ducts may need longer sampling tubes or more than one device.
- Wiring runs. The distance to the fire alarm panel and the HVAC controller sets the cable and conduit scope.
- Panel work. New points mean programming and testing at the fire alarm control panel.
- Filings and inspections. Work that changes the fire alarm or HVAC system may need DOB filings and sign-offs, which is separate from the hardware.
The most underestimated item is design coordination. When the mechanical drawings, the fire alarm drawings and the field conditions disagree, the cost is paid in change orders and re-inspections. That is why scope should be set by an engineer before pricing, not after.
Where projects go wrong
These are the failures we would expect any careful reviewer to flag on a New York duct smoke detector job:
- Wrong edition. A designer applies the 2022 rules to a building whose work was filed under the 2014 code, or the reverse.
- Missing units. A unit near the 2,000 cfm line is left off the detector schedule.
- Supervisory wiring. A detector is wired for a supervisory signal on a project that falls under the 2022 alarm-signal requirement.
- Detector in the wrong place. It sits before the filters on a supply duct or after the branches, or it does not see the full airflow.
- No access. Nobody can reach the device for the six-month cleaning.
- Treating it as room detection. Duct detectors are counted toward coverage that they cannot satisfy.
Our perspective
Duct smoke detection sits on the line between two trades. The mechanical engineer decides which fans stop and which dampers close. The fire alarm designer decides what the signal does at the panel. When those two sets of drawings are done by different firms, the gaps show up in the field, usually at inspection.
We keep mechanical, electrical, plumbing and fire protection design in-house, so one team reads the airflow, the damper schedule and the alarm sequence together. Our clients also have direct access to senior engineers, not account managers, so a question about whether a unit counts, or which code edition governs, gets answered by the person who will sign the drawings.
Our work in New York City runs through the NYC Department of Buildings and FDNY on a regular basis, and we design for how those agencies review filings. If you own or manage a building and are unsure whether your air handlers are covered, begin with the unit list and the filing history. That is the first thing we ask for.
Joseph
Getting your building reviewed
If you are planning a boiler or HVAC plant upgrade, a retrofit or a permit filing, the duct detector scope should be settled in design, on the same drawings as the mechanical work. Our Mechanical Engineering service covers HVAC system design. Our Fire Suppression Engineering service covers sprinkler and fire protection design. Building owners and property managers can see how we handle evaluations, equipment condition planning, plant upgrades and agency filings on our building owners page.

We are licensed in New York and Florida, and we coordinate with the NYC Department of Buildings and FDNY as part of permit filing. If you have a duct detector question on an existing building or a new design, contact us through our services page.
FAQ
Is a duct smoke detector the same as a smoke alarm?
No. A duct smoke detector is a sensor connected to the building fire alarm system that samples air inside an HVAC duct. It controls fans and dampers and reports to the panel. A smoke alarm includes its own sounder to warn occupants in a room.
Can duct smoke detectors replace smoke detectors in the rooms?
No. FDNY's study material says they are not a substitute for open-area smoke detectors, and Building Code §907.3.1 says duct detectors cannot replace required open-area detection. Smoke may not enter a duct when ventilation is off, or may be diluted when it is running.
Which HVAC systems need duct smoke detectors in NYC?
Under the 2022 NYC Mechanical Code, return-air and supply-air systems designed for more than 2,000 cfm need them, positioned as §606.2.1 and §606.2.4 describe. High-rise and underground buildings have further requirements in Building Code §907, and smoke dampers are tied to detector actuation under §607.3.3.2.
How often must duct smoke detectors be tested?
FDNY's study material says detectors connected to a fire alarm system should be visually inspected and cleaned at least every six months and tested for smoke entry and sensitivity at least annually. Duct detectors should also be checked to confirm they sample the airstream.
What changed in the 2022 code for duct detectors?
The DOB's 2022 code update presentation says duct detectors must now report as an alarm signal at the fire alarm control panel, with an FDNY-approved central station response. The 2022 Mechanical Code §606.1 also requires UL 268A listing, as reported by Green Light Expediting.
Sources
The code and agency documents cited above are named in the text: FDNY S-78/F-78 Certificate of Fitness study material, NFPA smoke alarm guidance, NYC Building Code §907, NYC Mechanical Code 2022 §606 and §607, DOB Buildings Bulletin 2014-004, and the DOB 2022 code update presentation on fire. Our own pages referenced in this guide:
